DIY lighting: Flush Mount Glass Bubble Chandelier


I’ve been dreaming of a glass bubble chandelier on top of my bathtub for months now, and I’ve finally got it. It’s a DIY lamp I made myself, and I did that for two reasons. First, I wanted a large flush mount bubble light, and that was almost impossible to find. But the main reason is that I don’t want the actual decorative part of the chandelier to have any electricity running on it. I know that’s weird, right?

The reason for this is because it is on top of my bathtub, and it is against the building code to put a chandelier on top of the bathtub. So I had to create a little of it and find a way to get the look of a chandelier without the decorative features hanging under the ceiling being wired. In other words, someone can stand in my bathtub full of water and touch any part of my chandelier, and it won’t surprise them because my chandelier is rather a decoration placed on the ceiling hanging in a recessed lighting. The recessed light provides light, but it is not connected in any way to the decorative part of the chandelier.

So here’s how my DIY glass bubble chandelier is made…

And here’s the whole scene with a bathtub, mural, and chandelier (with an unfinished wall on the left)…

And also, all the glass bubbles hang in a recessed light, which works, and gives light to all the glass bubbles. Here’s what it looks like when the recessed light is turned on and the other recessed lights are turned off…

It’s a beautiful beam of light, which is the perfect amount of ambient light if I want to bathe in foam at night.

So let me show you how I made this DIY glass foam light.

First, I started with a ceiling medallion. I bought it from Wayfair, and I chose the antique brass finish and the 24-inch size.

As you can see, the color I received was not the same as the color of the antique brass medallion on the Wayfair website, even though what I received was marked “antique brass” on the back. Well good. That’s nothing that can’t be solved with a pair of coats of spray paint. This is the spray paint I use …

The spray paint is perfect, and I have a perfect antique gold medallion…

Here’s a look at the light on top of the bathtub. As you can see, this is just a normal recessed light, and I passed it on to a separate switch from the other recessed lights in the room.

To install the medallion, I used washers, 2-inch screws, and drywall anchors to screw the medallion to the ceiling through small holes. I didn’t pull them very hard on the ceiling at this point. I left it a bit loose so I could attach the form where the glass bubbles would hang.

And the form I use is a flower basket I found on Amazon.

I planned this chandelier in December of last year (2021). That’s when I bought all the “bubbles” (which are frosted glass Christmas decorations), but I’ve been thinking for a long time about how I can attach all the bubbles. Then one day a few months later, I saw an Instagram reel from Chris Loves Julia with their bubble chandelier (costing $ 2500) installed and assembled, and when I saw the form where the foam glasses, I thought. , “Aw! That looks like a hanging flower basket! ”

So that’s exactly what I use. And I just attached it to the ceiling medallion using zip ties, which you can find in the electrical department at major home improvement stores. Just zip the hanging flower basket to the ceiling medallion, cut off the excess, and then tighten the screws the rest of the way so that the ceiling medallion fits the ceiling. Then I just used some gold acrylic paint I had on hand to paint the screws and washers before proceeding to the next step.

Next, I used standard size frosted glass Christmas decorations (about 2.5 ″) around the top of the basket. I just used the small hangers that were on the decorations to attach them to the wire basket so that it would be as close as possible.

And then I went on to another row, and then another, to cover as much as possible with the wire basket.

When I covered the basket nearby, I started adding large 4-inch decorations. Once again, I bought them last Christmas at the Hobby Lobby when they were all sold out. (I would only recommend buying them on sale during the Christmas season, because if you have to buy them in the off season, you’ll pay a ridiculous price for them.)

To hang the large ornaments, I used 12-gauge craft wire that I purchased at Michael’s…

Using my needle nose pliers with a wire cutter, I cut the wire to 4-inch lengths, and shaped one end into a loop hung on the ornaments.

When they were attached, I squeezed the trap so that it would be firmly attached to the decoration.

And then, still using my needle nose pliers, I shaped the other end to be a hook that attaches to the wire basket.

Once I attached each large ornament to the wire basket, I used my needle nose pliers to pinch the hook so it wouldn’t come off the wire basket. I will not lie. It was easier said than done, especially with the light more and more filled with bubbles, and it became a tight squeeze to get my pliers in the middle of all the decorations. But I did my best, and it took a lot of patience, but in the end I got them all.

In total, I used 34 of the major ornaments to make the entire chandelier. The ceiling medallion is 24 inches in diameter, to give you an idea of ​​the size.

I was so happy with what turned out. It has actually turned out a lot better than I thought, and it will fit the needs of this space. It hugs the ceiling, and since these decorative features have no electrical connection, there isn’t any violation of the construction code. But I still got the beautiful chandelier to look at over my bathtub.

And speaking of the bathtub, here’s the view from below. This is the view I got of the light as I took a bath in the bathtub.

And here is another direction…

I’m very seriously proud of how it turned out.

Here is the whole scene. Please ignore the unfinished walls in the rest of the room. ⁇

And here are a couple closer photos. I tried to get the faucet and the chandelier at a glance…

Very nice, isn’t it? I love it!

I actually think my little DIY glass bubble chandelier is better than the one I had in my original mock bedroom, which is from Pottery Barn (I think).

Once again, here is what the chandelier looks like when the light is turned on. This glow is so beautiful. It is with other lights that are also on…

And these are the other lights that are turned off…

Here’s the full look at the light turned on with the other recessed lights turned off…

That’s great for a DIY bubble light, isn’t it? I tried the bubble light without the medallion before (which you can see here), but I don’t really like it. So I considered other options, such as dyeing the bubbles a different color to the ceiling.

But in the end, all it takes is a medallion, and this one was specifically suggested by a commentator in a previous post. I think it’s perfect! And thanks to that medallion, the original frozen bubbles became perfect. I like that they kind of give the feeling of a cloud over the bathtub.



Source link

Leave a Reply

Your email address will not be published.